vps/docs/unifi-network.md

UniFi network configuration

Controller

Item	Value
Host	ubnt
Address	192.168.66.46
Deployment	Docker, jacobalberty/unifi:v9.5.21, host networking
Inform endpoint	http://192.168.66.46:9080/inform
MongoDB database / port	ace / 27117

Although 8080 is a common UniFi inform port, this controller uses 9080. All AP adoption and recovery procedures must use the endpoint above.

Inter-VLAN reachability

The AP management networks are routed by gw, 192.168.66.254. On 2026-08-05, a probe sourced from the LAN55 gateway (192.168.55.254) reached the controller (192.168.66.46) with 3/3 ICMP replies. The UAP-AC-Lite is online through the :9080/inform endpoint, which also confirms the required application path in practice.

LAN_IN contains explicit allow rules for 192.168.55.0/24 ↔ 192.168.66.0/24, but the firewall set is currently inactive (not attached to an interface). Treat the networks as bidirectionally reachable by default; do not rely on those inactive rules as an access boundary. Recheck this after attaching any LAN firewall policy or changing VLAN routing.

To inspect device records from the controller host:

docker exec -it unifi-controller bash
mongo --port 27117

use ace
db.device.find(
  { type: "uap" },
  { name: 1, ip: 1, model: 1, inform_url: 1 }
).pretty()

Managed access points

Name	Model	Management IP	Firmware	Management network	Inform port
U6 Lite	U6 Lite (UAL6)	192.168.66.6	6.7.54.15663	LAN66 (192.168.66.0/24, gateway 192.168.66.254)	9080
UAP-AC-Lite	U7LT	192.168.55.5	6.8.2.15592	LAN55 (192.168.55.0/24, gateway 192.168.55.254)	9080

AP MAC addresses are recorded only where operationally needed: U6 Lite 78:45:58:4d:cc:30; UAP-AC-Lite f0:9f:c2:20:04:e9.

SSH administration

Adopted APs use the SSH account configured in the controller, rather than the factory ubnt/ubnt credential. The password is stored in the password manager and must not be added to this repository.

In UniFi Network 9.5.21, configure it at:

Devices → Device Updates and Settings → Device SSH Settings
→ Device SSH Authentication

Use ssh zhiqiangf@AP_IP for the adopted-device account. Do not query or copy the controller's mgmt database setting into logs or documentation: it can contain the managed SSH password.

On 2026-08-06, key-only IPv4 SSH was verified for both managed APs using the zhiqiangf account. Verify future access without permitting password or keyboard-interactive fallback:

ssh -4 -o BatchMode=yes -o PasswordAuthentication=no \
  -o KbdInteractiveAuthentication=no -o StrictHostKeyChecking=yes \
  zhiqiangf@192.168.66.6 'mca-cli-op info'
ssh -4 -o BatchMode=yes -o PasswordAuthentication=no \
  -o KbdInteractiveAuthentication=no -o StrictHostKeyChecking=yes \
  zhiqiangf@192.168.55.5 'mca-cli-op info'

Both devices reported Connected to http://192.168.66.46:9080/inform during that verification. The AP shell maps this management account to UID 0, so treat it as administrative access.

Offline AP recovery

An AP can be reachable via ICMP and SSH but offline in the controller when its saved inform URL still points to port 8080. This occurred for UAP-AC-Lite after its inform configuration had diverged from the controller endpoint.

From the AP, inspect the active endpoint and test controller reachability:

info
nc 192.168.66.46 9080

The AP's BusyBox nc may not support -zv; use the plain nc invocation above when testing the TCP path.

If info reports http://192.168.66.46:8080/inform (or another obsolete endpoint), correct it. UniFi devices commonly require the command twice while adoption is completed:

set-inform http://192.168.66.46:9080/inform
set-inform http://192.168.66.46:9080/inform

Verify that the AP changes to connected/online in the controller.

Controller migration check

After a controller migration or restore, inspect stored device records for a stale default-port endpoint before treating an AP as faulty:

use ace
db.device.find(
  { inform_url: /8080/ },
  { name: 1, ip: 1, inform_url: 1 }
)

Do not include credentials or controller database dumps in incident notes.